Fireware XTM v11.3.1 CSP2 For XTM 1050, 8-series, 5-series, 2-series, e-series Edge, e-series Core/ Peak Appliance Build # 288054 WSM v11.3.1 or higher is needed to manage a Firebox running Fireware XTM 11.3.1 CSP. Resolved Issues: BUG56448: SIP registrations may fail when server sends NOTIFY BUG56000: SIP Forking (INVITE) with same call-id doesn't work BUG44587: RTP packets being sent out of the wrong interface due to wrong route lookup when using proxies BUG44571: FBX DHCP Server hands out addresses too slow due to DNS host name lookup. RFE56693: Improved ability to debug what licenses features are enabled on Firebox for better troubleshooting of licensing issues. BUG44585:Â Default WebBlocker exceptions should be more specific BUG55999:MSRP File-xfer doesn't work BUG56599: BOVPN may fail to rekey with NetScreen and Juniper Endpoints when using NAT in the BOVPN RFE41194: Host range or subnet for SSO exception list [need pm_fb.jar and pm_fb_rb.jar .. see below] BUG56593: Log SRV stops working when Management SRV log contain Japanese fonts [need wgpr.dll.. see below] Ability to configure 200 traffic management objects using policy manager [Need pm_fb.jar file... see below] Description of v11.3.1 CSP files available for download: pm_fb.jar -- Policy manager component. To install locate existing pm_fb.jar filed under C:\Program Files\WatchGuard\wsm11\pm\bin and replace with new component. pm_fb_rb.jar -- Policy Manager Component To install locate existing pm_fb_rb.jar filed under C:\Program Files\Common Files\WatchGuard\wsm11\lib and replace with new component. wgpr.dll -- log server component. The wgpr.dll needs to be installed in %SYSTEMDRIVE%\Program Files\Common Files\WatchGuard\wsm11\bin. Because wgpr.dll is used by all WSM applications (including Java apps) and servers, you must close all applications and stop all servers before the dll can be replaced. Note that this also applies to the WSC application. You can close WSC by right-clicking on the WSC taskbar icon and selecting Exit, and clicking on Yes in the confirmation dialog. Once wgpr.dll is replaced, you can run the following command-line to get WSC to show up in the taskbar again: \wsc\bin\wsc.exe Where is by default %SYSTEMDRIVE%\Program Files\WatchGuard\wsm11. XTM_OS_Core_Peak_11_3.exe -- appliance firmware install that will put the .wgu and sya-dl file on your PC for use by Policy Manager or WebUI XTM_OS_Edge_11_3.exe -- appliance firmware install that will put the edge sys-dl file on your PC for use by Policy Manager or WebUI XTM_OS_1050_11_3.exe -- appliance firmware to install 1050 sysa-dl file on your PC to upload to the 1050 using policy manager or the WebUI XTM_OS_XTM2_11_3.exe -- appliance firmware to install sysa-dl file on your PC to upload to the XTM 2-series using policy manager or the WebUI XTM_OS_XTM5_11_3.exe -- appliance firmware to install sysa-dl file on your PC to upload to the XTM 5-series using policy manager or the WebUI XTM_OS_XTM8_11_3.exe -- appliance firmware to install sysa-dl file on your PC to upload to the XTM 8-series using policy manager or the WebUI edge_11_3.exe -- edge upgrade file from v10.2.9 to v11.1CSP This file will convert your v10.2.9 configuration during upgrade utm_core_peak.down2fw.sysa-dl -- downgrade file for core/peak. If you need to downgrade to v10.2.8 use this file from the v11.1 Policy Manager WG-MVPN-SSL.exe -- Windows SSLVPN client George Grinnell | Director, Technical Support WatchGuard Technologies, Inc. | www.watchguard.com 206.521.3562 Direct . . . . . . . . . . . . . . . . . . . . . . . . Get red. Get secured